We've all done it one way or the other and hit a hole in are walls-ceilings that needs to be repaired. From a doorknob hitting the wall, a lacrosse ball going through the ceiling, or someone with a misguided fist. Repairing a damaged wall or ceiling may be easier than you thought. The tools you need are pretty basic and usually available one way or the other. Here's a list of what you will need and the steps to putting it in action.
Tools-Materials:
1. Sheetrock: Depending on the size of the hole-area you may need more or less sheetrock. For small repairs you can buy a tiny piece of sheetrock in your big box painting section that are pretty inexpensive. They're about the size of a floor tile or 1'x1'.
2. Straight edge: a ruler-level-book-something that has an even straight edge to draw a square to replace the old sheetrock.
3. Measuring tape: to measure the length x width to get your surface area to cut the new sheetrock. It doesn't have to be fancy or big just something to get the right number in inches to cut the new sheetrock.
4. Utility knife: A sharp utility knife is what you will use to cut the new sheetrock after you have measured the new dimensions for the replacement. You will have to repeatedly cut the same line on the sheetrock until the knifes blade goes all the way through for each sides cut. Knives are cheap. Everything you need can be bought at Harbor Freight on the cheap.
5. Coarse Sheetrock Screws: Buy a small box of 1.5 inch to use for fastening the new sheetrock and wood to the hole
6. Drill with Philips head bit: Using a power drill will significantly lower the headache threshold of using a screwdriver to complete this job. Buy one or borrow one you won't regret it.
7. Joint Compound: For smaller patches you will need nothing more than a gallon which are readily available at any hardware store.
8. Joint compound blades or knife 4 inch minimum. The four inch width of the blade is usually sufficient to apply joint compound to smaller patches evenly.
Once you have gathered the tools-materials it is time to get to work.
Step 1. Remove the damaged sheetrock using your utility knife. When removing the damaged area draw an even square around the damaged area so it is symmetrical. Once drawn simply repeatedly cut on the same line or side of the box you have drawn until the blade goes all the way through. You will know its through because it will become much easier to move the blade. Do this on all sides until you can cleanlily pull the bad piece of rock out. The damaged section should almost fallout because it's been cut so loose.
Step 2. Find or buy a small piece of wood that will fit in the hole you have cut on each side of it inside the wall. This part can be a little tricky but if you have a helping hand have them hold the piece of wood inside the wall while you fasten it with the sheetrock screws. Note: The piece of wood should be narrow enough to fit through the hole but long enough to extend a bit on each side when placed inside the wall to fasten it. So for instance, if you have a 3x3 patch to replace you are going to want about a 4-5 inch length of wood that can fir trough the 3 inch hole and extends beyond the length into the old sheetrock so it can be fastened.
Step 3. Measure and cut the new piece of sheetrock slightly smaller than the hole so it fits without cramming it in. To get the proper dimensions measure the length and width of the hole with your measuring tape and using your straight edge and utility knife draw a box in this case that is a little under 3x3 inches and cut out your new piece of sheetrock.
Step 4. Place the new piece of sheetrock in the hole against the wood you installed to back it and fasten it. Put a few screws into the sheetrock to fasten it to the wood backer.
Step 5. Open your joint compound and apply a thin coat filling in the cracks around the new piece of sheetrock and leveling out or making the area inside your patch even with the rest of the wall. You may need to apply at least two0thre coats depending on your skill level
Step 6. Once the patch has dried sand it flush-even with the existing area-prime -paint.
* Here's a video I did that gives you a better idea. It's a quick watch and if you are anything like me I'd rather see it so I have a better idea. Good Luck!
https://youtu.be/viisfjdpUDI?si=n1rV9J6ZKZxJcvsw
Donigan Painting EPA RRP Certified
224 Ross Park
Syracuse New York 13208
315-313-3254
Interior painting Syracuse NY, exterior painting Syracuse NY, Syracuse residential painting, Syracuse commercial painting, kitchen cabinet painting Syracuse NY, wall repairs, painting contractor Syracuse NY, painter Syracuse NY, house painting Syracuse NY, wallpaper removal, painters near me Syracuse NY, house painting services Syracuse NY, house painters Syracuse NY, local house painters Syracuse NY, Affordable house Painting Syracuse NY, Professional exterior painting Syracuse NY, new construction painting contractors Syracuse NY, Best house painters Syracuse NY, reliable oainters near me Syracuse NY, quality interior-exterior painting Syracuse NY, trusted painting company Syracuse NY, home painter syracuse ny, house painter syracuse new york, home painter in syracuse ny, syracuse new york interio exterior painting contractor